Supply & Apply of the Waterproof Repair & Sealant Tape 12" per LM

1- Polyurethane foam spray 30-35mm
2- Acrylic top coat spray (LAITE GREEN)

Supply and apply of approved quality waterproofing system for all substructure concrete:
1 - One coats of cold Bituminous Primer
2 - Supply and apply two layers of waterproofing membrane SBS 4mm thick.

ROOF WATERPROOFING / SAB® PRO 111 (MEMBRANE) SYSTEM:
1-Execute slope corners (skirting) 20cm*20cm along with the barbate.
2-Execute a Cavity 1.5*1.5 cm, along with the barbate over the skirting.
3-One coat of bituminous primed surface.
4-One layer of Membrane APP 4mm thick, 180 g/m2
5-Screed Concrete, 80mm Avg. 20/N - OPC 300 kg/m3
6-Execute slope corners 20cm*20cm along with the barbate.
7-Remove the ridges, then fill them with a sponge.
8-Supply and apply 1.5x1.5 cm mastic over the sponge.

Supply & Apply Coating of Containment Areas and Tanks

Supply and apply of approved quality waterproofing system for the roof (Combo Roofing System).

1- Polyurethane foam, 30 mm thick and density 40-45 Kg/m3.
2- Acrylic - Liquid protection coat (600mic.Thick).
3- Geotextile /Separation Layer 100 g/m².
4- Filler board/flexible sheet.
5- Concrete screed (20N / MM² - 300 OPC, 80MM AVE. Thick.) without ice.
6- Angle fillet (cement sand mortar ).
7- Expansion joint filler (Backing rod + Pu sealant).
8- Acrylic Topcoat final. (light Green).

The RAK Green Building Regulation ( Barjeel )
Supply and apply the approved quality waterproofing system for the roofs (Combo Roofing System).

1- Polyurethane foam, 60mm thick, and density of 40-45 kg/m³. ( UV 0.3 W/m²K ).
2- Acrylic - Liquid UV protection coat (600mic.Thick).
3- Geotextile /Separation Layer 100 g/m²
4- expansion separator material Fiberboard -at least 10 mm thick & no more than 16 square meters
5- Concrete screed (20N/M³ - 300 OPC, 80mm AVE. Thick.) without (Ice&Fibre)
6- Angle fillet (cement sand mortar ).
7- Remove the filler board/flexible sheet -stage (4).
8- Expansion joint filter (Backing rod and Pu sealant).
9- Acrylic Topcoat final

Supply & Apply of the Liquid Silicone Waterproofing Coating per M²

SAB® Crystal 410 concentrate and one more other supporting material.
• As preparation:
• Cleaning scope of work area properly.
• Spraying the outer side with water, the Property of this material it needs wet area to make the required strong interaction.
• Puncture the surface by making tiny holes, this will ensure perfect absorption.
• Cleaning these small holes and insures it dry; taking into consideration the whole area is still wet.

• Polyurethane foam for thermal insulation, 150-• • • •
• 155 mm thick and density, 45-50 Kg/m3.
• Liquid U.V protection coat (600mic.Thick).
• Geotextile /Separation Layer 120 g/m2
• Filler board/flexible sheet & cement stand mortar.
• Concrete screed (25N / MM2 - 300 OPC, 80MM AVE. Thick.) without ice.
• Angle fillet (cement sand mortar and SBR bonding agent).
• Expansion joint filter (Backing rod and Pu sealant).
• Acrylic Top coat final .

Responding The Green Building Regulation.

Supply and apply of approved quality waterproofing system for roof (Combo Roofing System) .

1- Polyurethane foam for thermal insulation , 65-70 mm thick and density 40-45 Kg/m3.
2- Rubberized bitumen (2) coat. UV Protection coat.
3- Geotextile /Separation Layer 100 g/m2
4- Concrete screed (26N / MM2 - 300 OPC, 70MM AVE. Thick.) without ice.
5- Angle fillet (cement sand mortar ).
6- filler board/flexible sheet .
7- Expansion joint filter (Backing rod and Pu sealant).
8- Acrylic Top coat final .

Supply and apply the approved quality system for pile head treatment and insulation 500 mm DIAMETER:-
1- Repair surface with cementitious grout
2- Treatment by using (Fosroc) super cast DC and super cast EP10